Secured by Design Platinum Sliding Gate SR1, SR2 & SR3
The Secured by Design LPS 1175 SR1 (A1), SR2 (B3) & SR3 (C5) Platinum Sliding Gate is a cantilevered gate which has been successfully withstood forcible attack to Security Rating 1 (A1) for 1 minute, Security Rating 2 (B3) for 3 minutes and Security Rating 3 (C5) for 5 minutes.
The Sliding Cantilevered Gate requires no ground track or support across the roadway. The gateleaf is supported by a main bottom beam, which slides 100mm above the road surface. The balance is provided by a unique runback track, which enables the gate to be fully projected across the roadway without tipping.
The Sliding Gate is 100% duty rated – designed for continuous & frequent use. Power is supplied from a single phase 230V supply.
Sliding Gates Safety control systems: Vehicle detector loops, photocells, ultra-sonic sensors and safety edges are available.
Sliding Gates Accessories: Signage, audible alarms and flashing beacons.
Sliding Gates Access controls: A wide range of access control systems are available.
Please click here to view the choice of Security Rated Gate Infills
Secured by Design LPS1175 SR1 (A1), SR2 (B3) & SR3 (C5) Platinum Sliding Gate Specifications
The Secured by Design LPS1175 SR1 (A1), SR2 (B3) & SR3 (C5) Platinum Sliding Gate
|Sliding Cantilevered Gate leaf Foundation
L:Runback length + 300mm x W:1000mm x D:300mm
L:600mm x W:1000mm x D:300mm
(Note: Power and control wiring ducts to be incorporated into foundations)
Sliding Gate Receptor Post Foundation
Minimum length of runback track:
For sliding gate apertures of 8m
Runback = Aperture x 1.5
For more information please contact the Technical Sales Department on
01293 422800 or email:
Industry standard electricals
|Electrical Requirements: 6 amp, 3 wire, 230v, 50hz, single phase supply.
Specifications subject to change and are dependant on product options. Please contact Frontier Pitts to request more information.
|Warning and information signs installed on the barrier boom such as ‘STOP’ ‘NO EXIT’ and ‘NO ENTRY’
Pedestrian Warning Sign
|Normally placed on the barrier cabinet. Warns pedestrian of the automatic barrier.
Traffic Light System
|Traffic Light systems are highly recommended to be installed with all road blocker and bollard systems to advise all users of its position. 100mm traffic light head can be pole or mounted on control cabinet
Vehicle Detector Loops
|Vehicle detector loops installed beneath the road surface to detect vehicles. This will prevent the automatic equipment from closing on a vehicle within the aperture. Safety induction loops cut into the road surface. This will prevent the gate from closing on a vehicle within the aperture.
|Safety Photocells produce beams of light which cross the road way to monitor vehicle and pedestrian movement. If an object breaks this beam, the automatic equipment will stop & reverse. On gate installations, two pairs of photocells are usually fitted. Ultra Sonic Sensors are also available.
Gate Safety Edge
|Safety Edges are normally fitted to automatic gates. However they can also be installed beneath a barrier boom. Safety edges prevent the barrier lowering on a person or vehicle in the event it is activated. Safety edges are flexible strips which, if depressed, send a signal to the power source to stop.
Pedestrian Guard Rail
|A Pedestrian Guard Rail (fence panels) should be fitted around the runback area of the sliding gate. This is to prevent serious injury to a person should they stray into that area whilst the gate is operating.
Weldmesh should be clipped to the gates infill bars infill to prevent pedestrians putting their limbs through.
Other infills include palisade pales, sheet and wood infills. For more information please Security Gate Infills page
|Sounders/Audible Alarms provide an audible warning that the automatic equipment is in operation.
|Flashing Beacons provide a visual warning that the automatic equipment is in operation.