Rising iBollards

The Automatic Rising iBollard is a retractable bollard, hydraulically powered barricade which has a lift height of 600mm.

Automatic Rising Bollards provide automated heavy-duty vehicle access control and protection against ram-raiding. These units bridge the gap between Automatic Barriers and Road Blockers in terms of security and cost.

100% duty rating – Automatic Bollards are designed for continuous and frequent use. Power requirement is supplied from a single phase 230v supply.

The Automatic Rising Bollards can be interfaced to any access control systems. Traffic Light System included as standard on all automatic bollard systems.

  • Lift Height: 600mm

Rising iBollards Specifications


The Rising iBollards

    Basic Specs

  • Lift height 600mm
  • More details

  • Automatic Bollard diameter: 215mm diameter
  • Automatic Bollard Finish – Stainless Steel finish
  • Automatic Bollard Control Cabinet: Zinc rich powder prime polyester powder coat white. Finish provides excellent corrosion protection.
  • Accessories Included: Industrial hydraulic pump drive unit, Motor protection, Security lock on cabinet door, Instantly Reversible, Override Switch, Switched fused supply, Mains indicator lamp, Reinforced hoses for long service life, Long life hydraulic seals
  • Speed of operation: 5-9 seconds *This is subject to a risk assessment to ensure the automatic equipment complies to BS EN 12453, depending on configuration
  • Duty Cycle: 100% duty rating
  • Safety: Vehicle Detector Loops, Safety Photocells, LED Traffic light heads
  • Controls: The programmable logic controller (PLC) with built in safety features will accept inputs from access control systems including access card, voice, etc. Push button is supplied as standard

Civil Engineering

Rising iBollards Foundations
600mm lift Rising Bollard Foundation: 800mm sq x 880mm deep
Note: Power and control wiring ducts to be incorporated into foundations.
Control Cabinet Foundations: 800mm SQ x D:300mm
It is recommended that the rising bollard’s control cabinet is installed within 10metres of the unit.

For more information please contact the Technical Sales Department on

01293 422800 or email:

[email protected]

Electrical Engineering

Industry standard electricals

Electrical Requirements: Single Phase, depending on configuration

Specifications subject to change and are dependant on product options. Please contact Frontier Pitts to request more information.


Photo Gallery



Warning and information signs installed on the barrier boom such as ‘STOP’ ‘NO EXIT’ and ‘NO ENTRY’

Traffic Light System

Traffic Light systems are highly recommended to be installed with all road blocker and bollard systems to advise all users of its position. 100mm traffic light head can be pole or mounted on control cabinet

Traffic Light Cage

Vandal resistant traffic light cages

Manual Handpump

In the event of a power failure, a hand pump/release can be provided to enable the manual raising and lowering of the blocker/bollard.

Hand drill to operate manual hand pump

Hand drill to operate manual hand pump on a Rising Terra Bollard.

Vehicle Detector Loops

Vehicle detector loops installed beneath the road surface to detect vehicles. This will prevent the automatic equipment from closing on a vehicle within the aperture. Safety induction loops cut into the road surface. This will prevent the gate from closing on a vehicle within the aperture.

Safety Photocells

Safety Photocells produce beams of light which cross the road way to monitor vehicle and pedestrian movement. If an object breaks this beam, the automatic equipment will stop & reverse. On gate installations, two pairs of photocells are usually fitted. Ultra Sonic Sensors are also available.

High Security Cabinet

Provides high security protection to the control cabinet of Frontier Pitts IWA14 & PAS 68 Anti Terra product range. Special Security cabinets can be fitted and tested to BRE 1175 with 6 point security locking mechanism and fire resistance to DIN 4102. High security mauer key lock, Class A, ECBS/ENV 1300 approved, with similar rating to BS EN 1143-1 1997.

Stainless Steel Cabinet

As standard, the road blockers/bollards control cabinet is shotblasted and finish with a final coat of polyurethane paint. However a Stainless Steel finish is also available as an option.
Subscribe to get the latest news about our products
We respect your privacy, we will not spam you.