LPS1175 Platinum Sliding Gate

LPS 1175 SR2 & SR3 Platinum Sliding Gate

The LPS 1175 SR2 & SR3 Platinum Sliding Gate is a cantilevered gate which has been successfully withstood forcible attack to Security Rating 2 for 3 minutes and Security Rating 3 for 5 minutes.

The Sliding Cantilevered Gate requires no ground track or support across the roadway. The gateleaf is supported by a main bottom beam, which slides 100mm above the road surface. The balance is provided by a unique runback track, which enables the gate to be fully projected across the roadway without tipping.

The Sliding Gate is 100% duty rated -  designed for continuous & frequent use. Power is supplied from a single phase 230V supply. 

Sliding Gates Safety control systems: Vehicle detector loops, photocells, ultra-sonic sensors and safety edges are available. For Sliding Gate Safety, please click here

Sliding Gates Accessories: Signage, audible alarms and flashing beacons.

Sliding Gates Access controls: A wide range of access control systems are available.

LPS 1175
Security Rating 2 & 3

Security Cantilevered Sliding Gate

Secures a maximum aperture 
up to 10m. Bespoke available 

Security Gates

LPS1175 Platinum Sliding Gate Specifications

Specifications subject to change and are dependant on product options.

Please contact Frontier Pitts to request more information.

Features

The LPS 1175 SR2 & SR3 Platinum Sliding Cantilevered Gate from Frontier Pitts

Variable widths up to 10,000mm. Bespoke available
Standard gateleaf height: 2400mm
Maximum gateleaf height: 4000mm
Construction: The sliding gate leaf is a fully welded construction of rectangular hollow section, low carbon steel to BS4848 Pt.2.  Standard colour range: Any colour in the RAL colour range
100% Operating duty cycle - designed for continuous & frequent use.
Typical operating speeds of 200-250mm/second* 
Depending on configuration.
Finish: Various options available, including:  Shotblasted, hot zinc sprayed, primed & finished with a final coat of polyurethane paint. Alternatively, acid dipped then hot galvanized available on smaller gates.
Various security infills available including bar, security weldmesh, sheet, and bespoke such as wood and ornate.
Sliding Gate Safety control systems: Vehicle detector loops, safety photocells, ultra-sonic sensors and safety edges are available. 
Sliding Gate Accessories: Signage, audible alarms and flashing beacons.
Sliding Gate Access controls: A wide range of access control systems are available. 
This is subject to a risk assessment to ensure the automatic equipment complies to BS EN 12453   

Civil Engineering

Cantilevered Sliding Gates require no ground track or support across the roadway

Cantilevered Sliding Gate Foundations

Sliding Gate leaf Foundation 

L:Runback length + 300mm x W:1000mm x D:300mm
L:600mm x W:1000mm x D:300mm 
(Note: Power and control wiring ducts to be incorporated into foundations)
Sliding Gate Receptor Post Foundation
Minimum length of runback track:

For sliding gate apertures of 8m

Runback = Aperture x 1.5

For sliding gate apertures of 8m+ 
Please contact the Technical Sales Department
on 01293 422800 

Electrical Engineering

Industry standard electricals

Electrical Requirements

6 amp, 3 wire, 230v, 50hz, single phase supply.

  • Only single phase supply required
  • Override switch inside cabinet
  • Switched fuse supply double pole insulator
  • Easy accessible fuse unit

Signage

Warning and information signs are recommended to be installed with all automatic equipment to advise users of its operation

Pedestrian Warning Sign

Normally placed on the barrier cabinet. Warns pedestrian of the automatic barrier.

Traffic Light System

Traffic Light systems are highly recommended to be installed with all road blocker and bollard systems to advise all users of its position. 100mm traffic light head can be pole or mounted on control cabinet

Safety Photocells

Safety Photocells produce beams of light which cross the road way to monitor vehicle and pedestrian movement. If an object breaks this beam, the automatic equipment will stop & reverse. On gate installations, two pairs of photocells are usually fitted. Ultra Sonic Sensors are also available.

Vehicle Detector Loops

Vehicle detector loops installed beneath the road surface to detect vehicles. This will prevent the automatic equipment from closing on a vehicle within the aperture. Safety induction loops cut into the road surface. This will prevent the gate from closing on a vehicle within the aperture.

Gate Safety Edge

Safety Edges should be fitted to all automatic gates. Safety edges prevent the gate closing on a person or vehicle in the event it is activated. Safety edges are flexible strips which are fixed to the edge of a gate where there is a risk of a crushing or shearing hazard. If the safety edge is depressed a signal is sent to the power source to stop.

Pedestrian Guard Rail

A Pedestrian Guard Rail (fence panels) should be fitted around the runback area of the sliding gate. This is to prevent serious injury to a person should they stray into that area whilst the gate is operating.

Gate Infill

876

Weldmesh should be clipped to the gates infill bars infill to prevent pedestrians putting their limbs through.

Other infills include palisade pales, sheet and wood infills. For more information please Security Gate Infills page

Sounder

Sounders/Audible Alarms provide an audible warning that the automatic equipment is in operation.

Flashing Beacon

Flashing Beacons provide a visual warning that the automatic equipment is in operation.